Design of Fastenings for Use in Concrete: The CEN/TS 1992-4 Provisions by Rainer MalléeDesign of Fastenings for Use in Concrete: The CEN/TS 1992-4 Provisions by Rainer Mallée

Design of Fastenings for Use in Concrete: The CEN/TS 1992-4 Provisions

byRainer Mallée, Rolf EligehausenTranslated byWerner Fuchs

Paperback | May 6, 2013

Pricing and Purchase Info

$83.00

Earn 415 plum® points
Quantity:

Ships within 1-3 weeks

Ships free on orders over $25

Not available in stores

about

The European pre-standard CEN/TS 1992-4 for the design of fastenings by means of headed studs, anchor channels as well as post-installed mechanical and chemical anchors is ready for use. The background and interpretation of the provisions related to the determination of actions and resistances based on limit state design, durability, fire resistance, fatigue and earthquake actions as required by CEN/TS 1992 are described in detail.

Selected chapters from the German concrete yearbook are now being published in the new English "Beton-Kalender Series" for the benefit of an international audience.
Since it was founded in 1906, the Ernst & Sohn "Beton-Kalender" has been supporting developments in reinforced and prestressed concrete. The aim was to publish a yearbook to reflect progress in "ferro-concrete" structures until - as the book's first editor, Fritz von Emperger (1862-1942), expressed it - the "tempestuous development" in this form of construction came to an end. However, the "Beton-Kalender" quickly became the chosen work of reference for civil and structural engineers, and apart from the years 1945-1950 has been published annually ever since.
Rolf Eligehausen, Prof. Dr.-Ing., studied structural engineering at the Technical University Braunschweig and gained his doctorate from the University Stuttgart. Following two years of research at the University of California Berkeley, he became professor for fastenings technology at the University Stuttgart in 1984. Professor Eligehau...
Loading
Title:Design of Fastenings for Use in Concrete: The CEN/TS 1992-4 ProvisionsFormat:PaperbackDimensions:170 pages, 9.5 × 6.8 × 0.54 inPublished:May 6, 2013Publisher:WileyLanguage:English

The following ISBNs are associated with this title:

ISBN - 10:3433030448

ISBN - 13:9783433030448

Reviews

Table of Contents

Introduction
Application
Fields of application
Basis of design
- General
- Verifications
- Partial factors
Derivation of forces acting on fasteners
- General
- Tension loads
- Shear loads
- Tension forces in a supplementary reinforcement
Verification of ultimate limit state by elastic analysis for post-installed fasteners (mechanical systems)
- General
- Tension load
- Shear load
- Combined tension and shear load
Verification of post-installed fasteners (chemical systems) for the ultimate limit state based on the theory of elasticity
- General
- Tension load
- Shear load
- Combined tension and shear load
Verification of ultimate limit state by elastic analysis for headed fasteners
- General
- Tension forces in the supplementary reinforcement
- Tesion load
- Shear load
- Combined tension and shear load
Verification of ultimate limit state by elastic analysis for anchor channels
- General
- Tension forces in the supplementary reinforcement
- Tension load
- Shear load
- Combined tension and shear loads
Plastic design approach, fastenings with headed fasteners and post-installed fasteners
- General
- Conditions of application
- Distribution of external forces to the fasteners of a group
- Design of fastenings
Durability
- General
- Fasteners in dry, internal conditions
- Fasteners in external atmospheric or in permanently damp internal exposure and high corrosion exposure
Exposure to fire
- General
- Basis of design
- Resistances under tension and shear load
Seismic loading
- General
- Additions and alterations to EN 1998-1:2004 (Eurocode 8)
- Verification of seismic loading
Outlook
References
Index